Spinning Report - Skeins 15 and 16

After finishing up Skein 14 I saw that I didn’t have that much left of my latest bag of Heinz 57 so I decided to spin it up and keep working on my drafting and also the fineness of my singles.  The top was a bit more than I typically spin on a bobbin (I did not weight it, but have calibrated my eye for how full I like my bobbins to get about 40 grams of single per bobbin) so when I reached that point and still had fiber left I did another bobbin.  This gave me four bobbins, two with about 40 grams and two with about 15 grams.  First I plied up the two 40 gram bobbins and ended up with this beautiful skein of fingering weight yarn.  It came in at 82 grams and 347 yards, or 4.21 yards/gram.  Spun on my Kromski at 16:1, plied on my Kiwi at 15:1.

After finishing that skein I took the two bobbins that had the smaller amount, and the leftovers from Skein 14 and weighed them all.  Then I put them on my Lazy Kate (lightest at top, heaviest at bottom) and made my first 3-ply yarn.  Spun on my Kromski at 16:1, plied on my Kiwi at 7.5:1.

It came out perfect.  100 yards, 36.5 grams, or 3.65 grams/yard.  I posted a picture of it in the Sheepspot Guild for the Friday spinning check-in, and was recognized in the spin of the week.  The challenge for May was a new to you ply, and this was mine.  I haven’t dyed it yet and I want to make some more 3-ply.  I’m thinking colorwork socks, but we’ll see what I end up doing with it.  I’m getting a little faster with the plying, still syncing my treadling with my drafting, but settling in to a nice rhythm.

Spinning Report - Skein 14

After finishing up those beautiful dyed tops that I had bought, I went back to the undyed Heinz 57 top and also dropped down to a smaller whorl (I had been working on my 12:1 ratio whorl, but have now switched to my 16:1 whorl).  Still working short forward draft, and trying to spin as thin and consistent a single as I could.  Here is the first bobbin.

It was not a fast spin, and the single on my second bobbin was definitely thinner than the first, as I had a fair bit left over (for me) even though the weight of the singles on each bobbin was comparable, and my final skein was only 68 grams (I usually shoot for about 80 grams).

I also put my smaller whorl on my Kiwi for plying (15:1).  I had a few issues with the plying - I did have a break on my first bobbin, but was able to rejoin it into the plied yarn okay (a better join than I’ve typically been able to do), but I also had some resistance from the wheel - so I decided it needed a drop of oil.  Unfortunately the oil bottle that came with my Kromski was 10 years old, and the plastic was the old plastic that grows brittle with age (and with exposure to oil, I suspect) and the bottle cracked when I squeezed it.  I thought that I had only gotten oil on my hands, but apparently I had also gotten oil on my drive wheel and more importantly on my drive band, but I didn’t realize that at the time.  No, I kept plying, and wondering where the strange noise was coming from, and why it wasn’t treadling as easily as it should.  I managed to finish the plying, and only after the skein was soaking did I take a look at the wheel and figure out all that had happened.  I cleaned everything up and wiped everything down, and treadled it for a few minutes, and it should be fine now.  Fortunately I had bought a new maintenance kit for my Kromski and it came with a new bottle of oil in a plastic bottle that is the better plastic.  I saved the old oil in a sealed container, and the application tip, which is really long.

I dyed the skein in Wool Tincture Dyes, in the color Deep Water.  It is a very uniform dye job, which made me happy, but that is probably because the dye packs and the jar is geared for a 100 gram skein, and mine was only 68, so it had plenty of room.  The yarn came out at a sport weight, although there are stretches that are thinner and some that are thicker.  Even with the challenges, I am happy with the result.

Skein 14:  240 yards, 68.1 grams or 3.5 yards/gram

Spinning Report - Skeins 10-13

I have been spinning regularly, every day, when possible.  I typically spin in the mornings, and usually for 30 minutes to an hour.  I find it very meditative, and it sets my brain (and mood) up nicely for the rest of the day.  Since my last spinning post on March 7, I have spun and plied over 800 grams of yarn.  All of these yarns were spun on my Kromski at a 12:1 ratio and plied on my Kiwi at a 9.5:1 ratio.

This is my 10th skein.  I went back to the Heinz 57, which I use as a sort of palette cleanser, and a way to reset myself after spinning a new base.  This skein came in at 135 yards and 86.4 g, or 1.56 yd/g and about 10 wraps per inch, so something between a worsted and a DK.  I dyed the skein with Plum from Wool Tincture Dyes.  I still have some variation in the dye take up, mostly where the ties are, even though I do try to tie loosely and I swish the fiber around in my dye jar.  I’m not overly concerned, as I’m not going for total uniformity.  Here is a picture of the skein untwisted.

Overall I am happy with both the singles consistency - there is not as much variation as I’ve had in the past, and the plying consistency.  I do like the set up I have with spinning on the Kromski and plying on the Kiwi.  I’m not sure what I will make with this yarn, but have been thinking about some fingerless mitts.

A little while ago I did an impulse buy of some of Rosie’s Multicolor Merino Tops from The Woolery, so I tackled them next and focused on my singles, trying to be consistent.  For each of the tops I used the same process:  I took the 250 g top out of the bag and shook it out, and then divided it into three equal sections length-wise.  Two of the sections I wrapped up in to a nest and set aside, then I took one section and divided it in half length-wise again, so that I had two pieces of top that were about the same length.  I then stripped the top in half, and then in half again, so I was working with about one quarter of the top at a time to keep the colors from blending too much.  All were spun using short forward draw and scotch tension.  I spun two bobbins from each of the three original sections of top, I wound the bobbins off the wheel and onto another bobbin and let them sit overnight (at a minimum) before plying.  I did not spin up all of the fiber and then mix the bobbins, which I know is recommended to minimize variations in the plied yarn by compensating for variations in the singles, but I wanted to see my inconsistency, not mask it.  I spun a section, and plied it, and then spun the next section and plied it, until I had spun and plied all three sections.

The first top that I grabbed was the Cornucopia colorway.

From left to right these are skeins 11a, 11b, 11c, and 11d.  As I settled in to spinning this top my singles settled in to a slightly thicker diameter.  When I was plying the first two bobbins I had a break, which I didn’t fix, so I ended up with two smaller skeins.

Skein 11a came in at 49 yards and 26.5 g, or 1.84 yd/g

Skein 11b came in at 76 yards and 44.5 g, or 1.69 yd/g

Skein 11c came in at 145 yards and 89.7 g or 1.62 yd/g

Skein 11d came in at 130 yards and 89.8 g or 1.44 yd/g

Next I grabbed the Valentine colorway.

From left to right these are skeins 12a, 12b, and 12c.  The singles on these three skeins are far more consistent.

Skein 12a came in at 115 yards and 79 g, or 1.46 yd/g

Skein 12b came in at 111 yards and 79.6 g, or 1.4 yd/g

Skein 12c came in at 121 yards and 84.3 g, or 1.44 yd/g

The last top is the Purple Haze colorway.

From left to right these are skeins 13a, 13b, and 13c, and on these skeins I went back to a thinner single, even thinner than what I had achieved on the first colorway.  I wanted to see how thin I could comfortably and consistently spin on the 12:1 ratio whorl.

Skein 13a came in at 154 yards and 78.1 g, or 1.97 yd/g

Skein 13b came in at 176 yards and 82.5 g, or 2.13 yd/g

Skein 13c came in at 161 yards and 83.6 g, or 1.93 yd/g

Overall, I am very happy with my spinning and plying on all of these skeins, and with the greater consistency I am achieving.  Although I have no idea what I want to make out of these three sets.

After finishing up these three tops I decided to go down a whorl size, so I set up with my 16:1 whorl and started spinning some more Heinz 57 top.  I haven’t finished my first bobbin yet, but I do have two ply-back samples:

After looking at the first ply-back sample (top) I decided I needed a bit more twist in my singles, which you can see in the bottom ply-back sample.  I’m pretty chuffed with the fineness I am achieving.  These are still short forward draw, although I did do a few inches of long draw just to see how it felt and looked - and it felt and looked pretty good.  Once I have spun short forward draw on all of my Kromski whorls (after the 16:1, I will do the 20:1), I will go back to the biggest whorl and practice long draw on all of them.

Simple Cowl - Finished!

I cast this on Tuesday, March 11, and finished it up Wednesday, March 12.  The yarn was spun up from a fiber club shipment from Paradise Yarns that I ordered on a whim.  It was a multicolored top - a mix of purples and yellows, and there were some other colors in there as well.  It was composed of 60% Extra Fine Merino, 25% Baby Alpaca, and 15% Tussah Silk.   I divided it in half, horizontally, so I could get two bobbins of singles, and then I stripped it lengthwise and spun it with absolutely no color management.  The resulting yarn was beautiful, and I’m sorry I don’t have a better picture of it.  It came out as worsted weight.

This is a picture fresh off the needles, before it went in for its blocking soak.  There is lots of color stuff happening, but it is pretty subtle.

And this is some of the yarn.  I actually had two skeins, a smaller one (this one) and a larger one, which I did not take a picture of.  The yarn was lovely - soft, silky, with great drape, and cushy.  It was also pretty consistent, which made me very happy.  Given how soft it was I knew I wanted something that I could wear close to the skin, so I cast on a simple cowl.  Just some rows of garter stitch at beginning and end and rounds and rounds of stockinette.  I even took out the end of round marker after I finished the first section of garter because I really just didn’t care and I wanted to make sure that I used up all of the yarn.  I only put the marker back in when I started the garter stitch for the end.

I spun the yarn on my Kromski, with a 12:1 ratio, and plyed it on my Kiwi, with a ratio of 9.5:1.  I even used a plying bracelet at the end to make sure I used up of the singles.

I really like having two wheels, one for spinning and one for plying so I don’t have to adjust them, and can have in process spinning on my Kromski while still finishing up other spinning efforts.

Pattern:  None - simple cowl, just cast on stitches, join in the round, and go

Yarn:  Handspun

Needle:  US 7 (4.5 mm)